Studio Equipment & Accessories

• The 099B extends the height of your light stand
• May be used as a hand-held light
• Microphone boom (with the proper, optional adapter).
• Aluminum construction 
• Black painted finish
• Extends from 35 to 92"

Learn More

The Kupo Junior Boom Arm is made from solid steel with a black coated finish that can support a payload up to 88.2lbs (40kg) at minimum extension and up to 22lbs (10kg) when fully extended. 

Learn More

This Kupo Mighty Runway Stand Base features an extra 4.7in (12cm) longer leg providing additional stability when it is necessary to make a boom rig. 

Learn More

KEY FEATURES

-Supports backdrops and roll paper up to 12’ wide and 12’ high
-Air-cushioned stands provide excellent stability
-4-section snap-together crossbar is quick and easy to set up
-Easily transport and store the kit with the included fabric case

Learn More

• 6 butterfly nuts equipped on the bar for a maximum of 6 lighting fixtures
• A compatible fit for a universal stand
• Solid steel square tube
• Length: 55.9in (1420cm)
• Max load 26.4lbs (12kg) for two sides. One side only, max load 13.2lbs (15kg).

Learn More

• Unique Patented innovative spring ring locking system allowing for easy set-up and take down.
• Base is five times stronger than aluminum
• Easily remove the column and attach to the Kupo Runway Base to create a strong sturdy and safe rolling stand.
• Fitted with captive locking t-knobs on the column.
• Limited two-year warranty

Learn More

• Replacement base for Master C- Stands with Turtle Base.
• Can be used as a very low stand
• Patented spring ring locking system enables you to open and close the base in under a second
• Zinc alloy casting for extra strength
• Max load: 66.1lbs (30Kg) Max height: 13.8" (35cm)

Learn More

• Unique Patented innovative spring ring locking system allowing for easy set-up and take down.
• Base is five times stronger than aluminum
• Easily remove the column and attach to the Kupo Runway Base to create a strong sturdy and safe rolling stand.
• Fitted with captive locking t-knobs on the column.
• Designed with three varied leg heights allowing stand bases to stack on set with equipment or nest together for storage

Learn More

• Fork has four pointed steel pins with a black coating
• Fork stabs into the foam center for stability, then stud can be placed in a grip arm or other receiver
• Weight: 0.4kg (0.88 lbs)
• Comes with a 5/8" baby stud
• Limited two-year warranty

Learn More

• Unique Patented innovative spring ring locking system allowing for easy set-up and take down.
• Base is five times stronger than aluminum
• Easily remove the column and attach to the Kupo Runway Base to create a strong sturdy and safe rolling stand.
• Fitted with captive locking t-knobs on the column.
• Limited two-year warranty

Learn More

• Unique spring locking system
• Extends to over 12' in height
• Extends from 39.4" - 66.9" (100cm - 170cm)
• No tools required
• Limited two-year warranty

Learn More

• Unique spring locking system
• Extends to over 12' in height
• Extends from 39.4" - 66.9" (100cm - 170cm)
• No tools required
• Limited two-year warranty

Learn More

• Quick mounting clamp for off-camera flash
• Alli Clamp with 5/8" baby studded tapped with a 3/8"-16 female thread and a baby receiver
• Steel construction
• Limited two-year warranty

Learn More

• Refillable 22.4lb (10.2kg) capacity sandbag
• Extra rivets, double stitching, interior bias binding for maximum strength
• Double handles on both top and bottom for more comfort. Hook and loop closure to support contents staying inside the bag
• Limited two-year warranty

Learn More

• 1/4"-20 male thread on one side
• Accepts any stud or tubing up to 5/8" (16mm)
• Mount monitors, off camera flashes or lightweight accessories
• Limited two-year warranty

Learn More

• Unique spring locking system
• Extends to over 12' in height
• Extends from 82.7"- 145" (210cm - 370cm)
• No tools required
• Limited two-year warranty

Learn More

• Adjustable arm allows positioning a camera lighting fixture or accessory within seconds
• Supports loads of up to 8.8 lbs (4 Kg)
• Large rubberized hand wheel allows joins to lock at same time for precise positioning
• Six milled flat surfaces for secure mounting
• Limited two-year warranty

Learn More

• 5/8" (16mm) socket inside
• attached to ball joint so it pivots from -45°to 90° and collar rotates 360°
• Includes 3/8"-16 thread which will accept the standard dot and camera accessories
• Weight: 0.86kg (1.90lbs)
• Limited two-year warranty

Learn More

• Dimensions: 5 1/2" x 3 5/8" x 1 3/8" | 14 cm x 9.2 cm x 3.5 cm
• Weight: 5 1/8 oz | 145 g

Learn More

• Large, powerful jaws
• 5/8" receiver
• Stud with 3/8"-16 female threads

Learn More

The best mounting system for Flex 1x2 and 2x2 LED mats For use with Scrim Jim Cine light control framework Standard baby pin for easy mounting to grip arms or heads Durable metal construction Heavy-duty hardware Learn More

• The best mounting system for Flex 1x1, 1x2, and 1x3 LED mats
• For use with Scrim Jim Cine light control framework
• Standard baby pin for easy mounting to grip arms or heads
• Durable metal construction
• Heavy-duty hardware

Learn More

• Allow for mounting of reflectors, foamcore, boards and more 
• Use with reflectors up to 72" wide 
• Removable grip mounts 
• Use as either a traditional boom style mount 
• Or center mount for added stability of larger reflectors 
• Features two telescopic sections; the arm collapses down to only 34"

Learn More

The Rock Solid Master Clamp is an indispensable piece of equipment designed to mount arms and gear to a wide array of round or flat surfaces.

Learn More

The Aero Cup Holder attaches to the Tether Table Aero to hold beverages, small tools or accessories and keep them near your workstation. The cantilevered design attaches to the side of the table and tucks away nicely when not in use.

Learn More